Подскажу. https://forum.armbian.com/index.php/topic/1605-wifi-access-point-problems-with-orange-pi-lite/
https://habrahabr.ru/post/188274/
# apt-get install dnsmasq
# apt-get install hostapd
# apt-get install iptables iproute2 procps haveged wireless-tools bridge-utils
не уверен, что весь этот мусор нужен, но так было, и такое ставят со скриптом create_ap (у меня он не завелся - не стал сильно упираться)
# groupadd -r dnsmasq && useradd -r -g dnsmasq dnsmasq
# service dnsmasq stop
прочищаем (можно забэкапить где-то) и редактируем раздатчик dhcp
# echo "">/etc/dnsmasq.conf && nano /etc/dnsmasq.conf
user=dnsmasq
group=dnsmasq
port=53
cache-size=100
domain-needed
bogus-priv
interface=wlan0
except-interface=ppp0
dhcp-range=10.0.0.2,10.0.0.10,12h
dhcp-authoritative
# service dnsmasq start
# reboot
раскомметнируем/поправим ссылку на конфиг тулзы точки доступа
# nano /etc/default/hostapd
#DAEMON_CONF="/etc/hostapd.conf" # before
DAEMON_CONF="/etc/hostapd/hostapd.conf" # after
Собственно вбиваем конфиг
# nano /etc/hostapd/hostapd.conf
interface=wlan0
driver=nl80211
ssid=OPIZeroWiFi
hw_mode=g
#ieee80211n=1
#uncomment for enable mode n
#ht_capab=[HT40-][SHORT-GI-40]
#uncomment for enable mode n
channel=6
wpa=2
wpa_passphrase=SuperDuperPassword
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP
auth_algs=1
macaddr_acl=0
Далее правим запуск сетки
# nano /etc/network/interfaces
# Wired adapter #1
allow-hotplug eth0
no-auto-down eth0
iface eth0 inet dhcp
#address 192.168.0.100
#netmask 255.255.255.0
#gateway 192.168.0.1
#dns-nameservers 8.8.8.8 8.8.4.4
# hwaddress ether # if you want to set MAC manually
# pre-up /sbin/ifconfig eth0 mtu 3838 # setting MTU for DHCP, static just: mtu 3838
# Wireless adapter #1
# Armbian ships with network-manager installed by default. To save you time
# and hassles consider using 'sudo nmtui' instead of configuring Wi-Fi settings
# manually. The below lines are only meant as an example how configuration could
# be done in an anachronistic way:
#
#allow-hotplug wlan0
#iface wlan0 inet dhcp
#address 192.168.0.100
#netmask 255.255.255.0
#gateway 192.168.0.1
#dns-nameservers 8.8.8.8 8.8.4.4
# wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
# Disable power saving on compatible chipsets (prevents SSH/connection dropouts over WiFi)
#wireless-mode Managed
#wireless-power off
allow-hotplug wlan0
iface wlan0 inet static
address 192.168.1.1
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
pre-up /sbin/ip link set wlan0 up
post-up /sbin/iptables -t nat -A POSTROUTING -j MASQUERADE && /bin/sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward"
# Local loopback
auto lo
iface lo inet loopback
# reboot
Строчку с post-up можно переработать по примеру
http://innerlife.i …i-plus-pppoe-iptables/
Ещё ссылки
http://innerlife.i …-pi-plus-wifi-hostapd/