MBedder, терминатор (09.03.2016 13:48, просмотров: 281) ответил imhoteb на У кого есть опыт запуска обоих внешних кварцевых резонатров в семействе ATXMEGA A, они перключаются на запуск через регистр XOSCSEL, если по раздельности запускать то все работает, проверяется легко выводом сихнроимпульса на выводы порта, а вот
На, лентяй. 1 ГЦ от RTC, работающего от часового кварца, выведен на ledport.ledpin, тактовая (32 МГц после PLL) - на PC7 .nolist
.include "ATxmega128A1def.inc"
.list
.equ ledport = PORTE_OUT ; Output port for LED
.equ ledpin = 4 ; LED pin position
.equ clkpin = 7 ; CLKOUT pin position
.def tmp = r16 ; Temporary register
;-----------------------------------------------------------------------------------------
.macro stsi
;
; Writes an 8-bit immediate value to a 8-bit direct RAM location.
; Usage: stsi addr,value
; Uses/trashes a tmp register for operation.
;
ldi tmp,@1
sts @0,tmp
.endm
;-----------------------------------------------------------------------------------------
;-----------------------------------------------------------------------------------------
.macro outi
;
; Writes a 8-bit immediate value to an 8-bit i/o SFR.
; Usage: outi IOREG8,value.
; Uses/trashes a tmp register for operation.
;
ldi tmp,@1
out @0,tmp
.endm
;-----------------------------------------------------------------------------------------
.cseg ; Start of Code segment
reset:
rcall init_ports ; Initialize ports
rcall init_osc ; Initialize oscillator
main:
lds tmp,RTC_CNT+0 ; Dummy LSB read required for 16-bit SFR access
lds tmp,RTC_CNT+1 ; Read RTC_CNTH
bst tmp,6 ; Copy RTC_CNTH 2 Hz toggling bit to T bit
lds tmp,ledport ; Read LED port
bld tmp,ledpin ; Paste T bit to tmp.ledpin bit position
sts ledport,tmp ; Copy tmp to LED port - the LED should blink at 1 Hz rate (0.5 s lit, 0.5 s dark)
rjmp main
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Oscillator initialization:
;
init_osc:
stsi OSC_XOSCCTRL,OSC_FRQRANGE_12TO16_gc | OSC_XOSCSEL_XTAL_16KCLK_gc ; Set up XOSC freq range and startup time
stsi OSC_CTRL,OSC_XOSCEN_bm ; Enable 16 MHz quartz oscillator
stsi OSC_PLLCTRL,OSC_PLLSRC_XOSC_gc | 2 ; Select XOSC as PLL source and set PLL multiplication factor to 2 (32 MIPS)
xt16m_stab:
lds tmp,OSC_STATUS ; Read OSC_STATUS
sbrs tmp,OSC_XOSCRDY_bp ; Wait until a 16 MHz quartz oscillator is stable (optional)
rjmp xt16m_stab
stsi OSC_CTRL,OSC_XOSCEN_bm | OSC_PLLEN_bm ; Enable PLL
PLL_stab:
lds tmp,OSC_STATUS ; Read OSC_STATUS
sbrs tmp,OSC_PLLRDY_bp ; Wait until a PLL is stable
rjmp PLL_stab
outi CPU_CCP,0xD8 ; Unprotect the CCP protected i/o register
stsi CLK_CTRL,CLK_SCLKSEL_PLL_gc ; Set a PLL as a system clock source
stsi RTC_CTRL,RTC_PRESCALER_DIV1_gc ; Select non-prescaled RTC clocking
stsi CLK_RTCCTRL,CLK_RTCSRC_TOSC32_gc | CLK_RTCEN_bm ; Set 32,758 Hz crystal oscillator as an RTC clock source and enable RTC
ret
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Port initialization
;
init_ports:
stsi PORTE_DIRSET,1<<ledpin ; LED pin = output
stsi PORTC_DIRSET,1<<clkpin ; CLKOUT pin = output
stsi PORTCFG_CLKEVOUT,PORTCFG_CLKOUT_PC7_gc ; Route system clock to PC7
ret
;------------------------------------------------------------------------------